35 recall campaigns found. Plus 51 owner complaints.
Ford Motor Company (Ford) is recalling certain 2025-2026 Bronco and Bronco Sport vehicles. The Instrument Panel Cluster (IPC) may fail at startup.
Ford Motor Company (Ford) is recalling certain 2021-2026 Ford Bronco and 2021-2024 Ford Edge vehicles. The Accessory Protocol Interface Module (APIM) may overheat and shutdown, which can prevent the rearview camera image from displaying as intended.
Ford Motor Company (Ford) is recalling certain 2024 Ranger, and 2024-2025 Bronco vehicles. The front upper control arm ball joint nut may not have been installed or tightened properly, allowing the front upper control arm to detach from the knuckle assembly.
Ford Motor Company (Ford) is recalling certain 2024-2025 F-150, Bronco, 2024 Ranger, 2025 Mustang, Explorer, and Aviator vehicles. The transmission valve body may have been machined incorrectly, which can cause reverse gear failure, or unexpected forward movement in reverse or neutral gear.
Ford Motor Company (Ford) is recalling certain 2025 Bronco vehicles. The front upper control arm ball joint nut may be missing or tightened improperly, allowing the front upper control arm to detach from the knuckle assembly.
Ford Motor Company (Ford) is recalling certain 2025 Ranger, Lincoln Nautilus, Mustang, Maverick, Explorer, Escape, Lincoln Corsair, Bronco Sport, and Bronco vehicles. The exhaust gas recirculation (EGR) valve may fail, resulting in an unexpected loss of drive power.
Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Ford Motor Company (Ford) is recalling certain 2024-2025 Bronco vehicles. The front lower control arm fasteners may not have been tightened properly, allowing the control arm to detach from the frame.
Ford Motor Company (Ford) is recalling certain 2025 Ranger and Bronco vehicles. The bolts that secure the driver's seat frame to the body may be loose or missing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 207, "Seating Systems."
Ford Motor Company (Ford) is recalling certain 2024-2025 Bronco and Ranger vehicles. The front upper control arm ball joint fastener may be missing or tightened improperly, allowing the front upper control arm to detach from the knuckle assembly.
Ford Motor Company (Ford) is recalling certain 2025 Bronco four-door vehicles. The left-hand rear door may be able to be opened from inside the vehicle when the child safety lock is in the "ON" position.
Ford Motor Company (Ford) is recalling certain 2025 Bronco vehicles. The active vent flap on the passenger side may prevent the air bag from deploying as intended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Ford Motor Company (Ford) is recalling certain 2025 Lincoln Navigator, F-150, Expedition, Bronco, and Ranger vehicles. The Electronic Brake Booster (EBB) module may malfunction while driving or when the driver is utilizing an Advanced Driver Assistance System (ADAS) feature, resulting in a loss of power brake assist.
Ford Motor Company (Ford) is recalling certain 2025 Bronco and Ranger vehicles. During manufacturing, the windshield may not have been properly bonded to the vehicle, allowing it to detach in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 212, "Windshield Mounting."
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were repaired incorrectly under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco, Explorer, Lincoln Aviator, F-250 SD, F-350 SD, F-450 SD, F-550 SD, 2021-2022 Lincoln Navigator, Mustang, F-150, and 2022 Expedition vehicles. The low-pressure fuel pump may fail, which can result in an engine stall while driving.
Ford Motor Company (Ford) is recalling certain 2025 Lincoln Navigator, F-150, Expedition, Bronco, and Ranger vehicles. The Electronic Brake Booster (EBB) module may malfunction while driving or when the driver is utilizing an Advanced Driver Assistance System (ADAS) feature, resulting in a loss of power brake assist.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously remedied under recall 22V-825. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Ford Motor Company (Ford) is recalling certain 2022-2023 F-150, Mustang, Explorer, Bronco, and 2023 Lincoln Aviator vehicles equipped with automatic transmissions. The transmission may contain a loose bolt which could prevent the transmission from engaging the park gear, although the gear shifter position may indicate that the vehicle has been shifted to "PARK."
Ford Motor Company (Ford) is recalling certain four-door 2021-2022 Bronco vehicles. The passenger-side rear door may be opened from inside of the vehicle when the child safety lock is in the "ON" position.
Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."
Ford Motor Company (Ford) is recalling certain 2023 Bronco Wildtrak and 2022 Bronco Raptor vehicles. Internal damage to the steering gear may require increased steering effort or cause the steering wheel to lock-up.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with rearview camera systems and 8-inch screen displays. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles. The right or left side impact sensors may not be properly secured to the vehicle.
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles built with the 5-Door body style. The first-row seat belt latch plates may be difficult to access from their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco, 2023 Super Duty F-250, and 2019-2023 Ranger vehicles. The Tire and Loading Information (TREAD) label states the incorrect load carrying capacity, which can result in an overloaded vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco, F-150, Edge, Explorer, Lincoln Nautilus, and Lincoln Aviator vehicles equipped with either a 2.7L or 3.0L Nano EcoBoost engine. The engine intake valves may break while driving, which can result in engine failure and a loss of drive power.
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco vehicles. The rear shock absorbers may corrode and fail, resulting in detachment of the external reservoir.
Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco vehicles. The 360-degree view camera may not display a rearview image when the vehicle is placed in reverse.
Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.
Ford Motor Company (Ford) is recalling certain 2021-2023 Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.
Ford Motor Company (Ford) is recalling certain 2021-2022 Bronco vehicles equipped with 8-inch SYNC infotainment screens that were previously repaired incorrectly under recall number 23V165. The rearview camera image may still be displayed after a backing event has ended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Ford Motor Company (Ford) is recalling certain 2021 Ranger and Bronco vehicles. The cruise control radar module was misaligned during production.
Ford Motor Company (Ford) is recalling certain 2021 Bronco vehicles. During passenger air bag deployment, an air bag vent could open prematurely and result in an improper deployment. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."
Ford Motor Company (Ford) is recalling certain 2020-2023 Lincoln Aviator, 2018-2021 Lincoln Navigator, 2022-2023 Ford Transit, and 2021 Ford Bronco vehicles. The rearview camera, or 360-degree view camera if equipped, may not display a rearview image when the vehicle is placed in reverse.
*Question 1 The top part of the Fender Flare on rear driver side was not properly welded/glued to bottom part of Fender Flare. It peeled off and flew while driving down the highway. *Question 2 The top fender flew off while i was driving. It could have hit another car behind. I also don't feel safe having the other fenders on my vehicle. If one's faulty, i have concerns the others will also come apart while driving *Question 3 Took my vehicle to dealership service center to report the incident (dealership: Group 1 Ford of Kennesaw). They took pics of the faulty fender and asked me to open a case with Ford Customer Service. The dealership said Ford was aware of the issue, but they couldn't replace because the part is not under any current warranty programs. Ford's manufacturer customer service made the same excuse. Asked for email confirming my case complaint.. they didn't send documentation (case # CXH-07394045-C3Y9M4) *Question 4 I called the manufacturer's customer service to review the incident with the dealership. They wouldn't cover the replacement because my vehicle had just exceeded the milage on their limited Bumper-to-Bumper Warranty..which is 36,000 or 3 years. My Bronco is only 2 years. I've never driven it off road and have been taking it to the dealership regularly for routine maintenance. The fender flare is an original factory part that should not have come apart while I was driving. Was surprised to see it fly off while driving, until i did a google search and found that this has happened to many other Bronco owners while driving. I've seen many owners post pics with the same exact part come off while driving. I'd be happy to share multiple links as evidence of the safety concern with this fender part. *Question 5 No signs until the part flew and we could see that fender wasn't properly welded together. Again, my vehicle has been taken to the dealership routinely for maintenance and they didn't notice the issue until the part came off.
There was a pot hold hole about 30 ft from a stop light. I was coming to a stop but once I hit the pot hole the breaks malfunctioned. I pumped the breaks 2-3 times. They did not reengage. This fault caused me to rear end the car in front of me at the stop light.
Vehicle: 2024 Ford Bronco Outer Banks Mileage: Approx. 15,000 The molded-in-color (MIC) composite hardtop panels have developed significant cracking across all four removable roof sections. Cracks are present on the driver-side front, mid, rear, and passenger-side panels. The cracking appears to originate within the composite material and has progressively worsened over time. The vehicle and affected panels are available for inspection upon request. The hardtop is part of a rollover-rated vehicle and contributes to structural integrity and occupant protection. Progressive cracking raises concern about reduced structural performance in a rollover. Additional risks include continued material degradation, potential panel instability at highway speeds, and water intrusion affecting electrical components. The condition has been visually inspected and confirmed by our Ford dealership, which verified cracking on all four panels. The vehicle has not been involved in any accident and has not been inspected by police or insurance representatives. The cracking was not caused by impact, misuse, improper storage, or improper removal. The hardtop has only been removed approximately five times since purchase, with all panels removed together only once, and removal was performed carefully according to manufacturer guidance. The hardtop is currently being replaced under the bumper-to-bumper warranty. However, replacement does not address the underlying concern if the material or manufacturing process is defective. Numerous other Ford Bronco owners have reported similar cracking, including multiple replacements. There were no warning lamps or messages prior to the cracking. The issue was first noticed at approximately 13,000 miles and has continued to progress. Given the low mileage, limited removal, dealership confirmation, and widespread similar reports, this appears to be a potential systemic material defect that warrants further investigation and a permanent corrective act.
Brakes did not engage. Rearended another driver. Have not gotten it to dealer yet. Police report made. Insurance working on claim. Need to get fixed first before getting it to the dealer to check systems. Found warning messages in the Ford app after incident, but nothing on dashboard to signal an issue.
The contact owns a 2024 Ford Bronco. The contact stated that while driving approximately 65 MPH, the brake warning light illuminated, and the brake pedal needed to be depressed with more force. The contact stated that the brake pedal was soft and there was no pressure on the pedal. The vehicle was taken to the residence. The vehicle was then taken to a dealer, where it was diagnosed and determined that the brake vacuum hose was leaking and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was approximately 48,000.
I am writing regarding my new Ford Bronco vehicle, VIN: [XXX] , purchased in November 2024, currently with 7,151.5 km. I recently received Ford’s official notice advising that the engine block heater in this vehicle may develop a coolant leak which could result in an electrical short circuit when the system is plugged in. This is a serious manufacturing and safety defect that existed at the time of sale. Due to the nature of this hazard, I am not operating the vehicle, as it has been placed it on storage insurance. The vehicle has not been driven since receiving Ford’s notice in order to mitigate risk and prevent potential damage or injury. Under Manitoba’s Consumer Protection Act and the Sale of Goods Act, a new vehicle must be of acceptable quality, safe, durable, and fit for its ordinary purpose. A vehicle delivered with an admitted safety defect fails to meet these legal requirements. Accordingly, I am formally exercising my right to rescind the sales contract and cancel the related financing agreement. I am kindly requesting a full buy-back, including refund of all payments made to date, payoff of the remaining loan balance by Ford or the dealer, and the cancellation of the financing agreement with no negative credit impact. I would appreciate a written response from you within five (5) business days so that we may proceed toward a timely and appropriate resolution. Sincerely, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2024 Ford Bronco. The contact stated that while driving the vehicle at night, the headlights failed to provide adequate illumination and created a visibility hazard for the driver. While inspecting the vehicle, the contact discovered that there was condensation inside the front headlight assemblies, which caused the illumination from the headlights to be reduced. The contact indicated that the failure occurred while the temperature was below 50 degrees. The cause of the failures was not yet determined, and the vehicle was not repaired. The manufacturer and the local dealer were notified of the issue. The failure mileage was 3,500.
While driving on the interstate in light snow and mostly clear and semi dry roads, ice accumulates on both the head lights and the foglights to a degree that they no longer project enough light to see far enough ahead at even moderate speeds. When I pulled over to inspect them, the surface was coated with a mix of ice and dirt rendering them useless. Ambient temperatures were between 24 and 30 degrees. It seems that the LED lights lack enough heat to protect from ice accumulation and a heat element of some type should have been included given the placement of the lights being somewhat recessed and that allows for accumulation. Obviously in pre-dawn darkness this produced an unsafe operation of a vehicle at highway speeds due to not being able to see the road far enough in advance. As far as I know it has not been addressed or noticed by Ford since there is no information about this in their manual. I have seen aftermarket products that heat the light surface and prevent the accumulation of ice - Ford should retrofit something to prevent the accumulation of ice on light surfaces.
The contact owns a 2024 Ford Bronco. The contact stated that while the defroster was engaged, the windshield cracked on the driver’s side. The crack started at the bottom of the windshield and spread to approximately 7-inches. The contact had not taken the vehicle to a local dealer or a glass repair shop to be repaired. The vehicle was not diagnosed or repaired. The contact researched online and related the failure to an issue with the OEM windshield. The manufacturer was not informed of the failure. The failure mileage was approximately 3,000.
The caliber seized causing the brake pad the fall and destroy the rotator. No brake indicators like turned on to advised of an issue. Ford does not want to take full responsibility for the faulty part that could have caused a major accident. Ford case# CXH06202259-S8K4B1. The vehicle is still at Ford for the repair so I don't have the repair documents yet.
We'll email you when a new recall is issued. No spam, unsubscribe anytime.